Welding machines
CHF218.–
Stahlwerk Welding machine MIG MAG 160 M IGBT 5 in 1 combi device with 160 amps
Best selling Welding machines from Stahlwerk
On this page you'll find a ranking of the best Stahlwerk products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.
1. Stahlwerk Welding machine MIG MAG 160 M IGBT 5 in 1 combi device with 160 amps
Steelworks MIG MAG 160 M IGBT - 5 in 1 combination welding machine with real 160 amperes
FLUX cored wire suitable, MIG MAG, Lift TIG with MMA E-Hand.
Note: Observe the correct amperage for a perfect welding result: For welding with 0.6 wire
at least 60 amps
Tig | MMA: 40-160 A Protection class: IP21s Mains voltage: 1 x 230 V AC (+-15%) Mains frequency: 50/60 Hz Maximum mains current (I1MAX) MIG/MAG | Tig | MMA: 26.3 A | 19.5 a | 31.5 A Maximum effective mains current (I1eff) Mig/Mag | Tig | MMA: 8.3 a |. 6.2 A | 10 A Weight: 4.5 kg Dimensions L x W x H (mm): 320 x 140 x 260 Mains connection: CEE 7/7 Schuko plug Standards: IEC 60974-1; EN 60974-10 (class A) Scope of delivery 1 x Welding machine Stahlwerk MIG 160 M IGBT 1 x Professional MIG welding torch AK-15 / hose package 2 metres. This is permanently installed on the device 1 x 3-piece MIG accessory set (this is already pre-assembled on the MIG/MAG torch): 1 x gas nozzle 1 x contact tip 0.8 mm 1 x gas nozzle holder 1 x contact tip M6 x 28 - 0.8 mm 1 x contact tipM6 x 28 - 1.0 mm 1 x welding shield 1 x 0.5 kg filler wire reel 0.8 mm 1 x earth cable 3 metres 1 x electrode holder 3 metres 1 x wire brush1 x slag hammer 1 x quick coupling for pressure reducer 1 x gas connection hose with quick coupling 5 metres 1 x wire guide roll 0.6 mm & 0.8 mm (0.8 mm & 1.0 mm is already installed in the device) 1 x protective cover
2. Stahlwerk FLUX 160 ST Digital welding machine with 160 A, synergic wire feed
Properties
Flux-cored wire welding (FLUX) - welding without shielding gas. Welding with flux-cored wire is based on a similar process to MIG MAG welding, with the difference that no shielding gas needs to be supplied in this process.
Note: The device is not intended for use in residential areas where power is supplied via a public low-voltage supply system. It may be difficult to ensure electromagnetic compatibility in these areas due to both conducted and radiated interference.
Technical data
Model: Stahlwerk FLUX 160 ST digital welder
Output current: 40 - 160 A
Duty cycle (40°C): 10 % at 160 A / 100 % at 50.6 A
Protection class: IP21S
Mains voltage: 1 x 230 V AC
Mains frequency: 50/60 Hz
Weight: 5.9 kg
Dimensions L x W x H (mm): 375 x 175 x 290
Mains connection: CEE 7/7 Schuko plug
Standards: IEC 60974-1; EN 60974-10 (Class A)
Certified by: TüV Rheinland LGA Products GmbH
Scope of delivery
1 x Stahlwerk FLUX 160 ST digital welding machine
1 x Stahlwerk FLUX AK14 / MB14 welding torch for wire thicknesses from 0.8 to 1.0 mm, 9 mm connecting mandrel with wire feed-through, 2-pin connection for switching operations
1 x earth cable 3 m (Ø 16 mm²)
1 x nozzle holder (pre-assembled on burner)
1 x contact tip 0.8 (pre-assembled on burner)
2 x contact tips 0.9
2 x filler wire nozzles
2 x wire guide rollers 0.6 mm / 0.8 mm, 0.8 mm / 1.0 mm (already installed in the device) - all guide rollers are knurled
1 x slag hammer
1 x protective cover
Welding machines
CHF199.–
Stahlwerk FLUX 160 ST Digital welding machine with 160 A, synergic wire feed
3. Stahlwerk Combination welder AC/DC TIG 200 ST IGBT 200 amps
Properties
AC/DC TIG welding - alternating current (AC) and direct current (DC). Welding of almost all metals, such as steel, stainless steel, aluminium, copper and many more.
2 in 1 combination device - TIG & MMA welding is possible up to 200A.
IGBT technology - The latest and most modern transistor technology enables high performance welding! No transformer, no MOSFET, state-of-the-art IGBT!
Technical data
Output current TIG / MMA: 30-200 A
Protection class: IP21S
Insulation class: F
Mains voltage: 230 V AC (+-15%) / 1 ~ (single-phase)
Mains frequency 50/60 Hz
Maximum mains current (I1max) (TIG / MMA): 27.7 A / 39.7 A
Maximum effective mains current (I1eff) (TIG / MMA): 14.5 A / 13.5 A
Weight: 11.5 kg
Dimensions L x W x H (mm): 455 x 220 x 370
Mains connection: Schuko type CEE 7/7
Standards: IEC 60974-1; EN 60974-10 (Class A)
Scope of delivery
1 x Steelworks AC/DC TIG 200 ST IGBT welding machine
1 x Professional TIG welding torch WP-26F / hose package 3 metres* with flexible torch head and kink protection on the gas connection
1 x TIG TIG accessory set 8 pieces:
3 x gas nozzles sizes: 5, 6, 7
1 x clamping sleeve size 1.6
1 x clamping sleeve housing size 1.6
2 x burner caps - one short and one long
1 x universal tungsten electrode 1.6 mm
* Pre-assembled accessories from the illustration of the welding torch are included in the 8-piece set
1 x earth cable 3 metres
1 x electrode holder 3 metres
1 x wire brush
1 x slag hammer
1 x Gas connection hose with quick coupling 5 metres
1 x Snap-on connection set
1 x protective cover
4. Stahlwerk MIG MAG 200 ST IGBT
Properties MIG/MAG: Gas metal arc welding in which shielding gas or mixed gas is used to protect the seam from oxidation. Flux-cored wire: Welding with flux-cored wire is possible with all MIG ST IGBT devices. No shielding gas is required for this special wire. Automatic wire feed: The speed of the wire feed adapts automatically to the welding current. Voltage: The wire burn-off can be set separately.
Technical data:
- Output current MIG/MMA: 40-200 A
- Protection class: IP21S
- Mains voltage: 230 V AC (+-15%) / 1 ~ (single-phase)
- Mains frequency: 50/60 Hz
- Maximum rated current (I1max) MIG/MAG: 34.6 A / 40 A
- Maximum effective mains current (I1eff) MIG/MAG: 10.9 A / 12.6 A
- Weight: 11.8 kg
- Dimensions L x W x H (mm): 450 x 240 x 370
- Mains connection: Schuko type CEE 7/7
- Standards: IEC 60974-1; EN 60974-10 (Class A)
Scope of delivery:
- 1 x Stahlwerk MIG 200 ST IGBT welding machine
- 1 x Professional MIG welding gun AK-15 / 3 metre hose package with Euro central connection
- 1 x 3-piece MIG accessory set (this is already pre-assembled on the MIG/MAG torch):
- 1 x gas nozzle
- 1 x contact tip 0.8 mm
- 1 x gas nozzle holder
- 1 x earthing cable 3 metres (25 mm²)
- 1 x electrode holder 3 metres (25 mm²)
- 1 x Gas hose with quick coupling 5 metres
- 1 x connection set for pressure reducer
- 2 x contact tips (0.8 / 1.0 each)
- 1 x assembly spanner
- 1 x wire brush
- 3 x wire guide rolls (0.6 mm/0.8 mm, 1.0 mm/1.2 mm, 0.8 mm/1.0 mm is already installed in the device)
- 1 x protective cover.
5. Stahlwerk Flux 140 ST
The Flux 140 ST Digital welding machine from Stahlwerk is a powerful flux-cored wire welding machine that is suitable for a wide range of applications. It enables welding without shielding gas, making it a practical choice for various projects. With a maximum welding current of 140 A and a synergic wire feed that automatically controls the wire feed speed via the welding current, this device offers a user-friendly and efficient welding experience. The clear digital display makes it easy to read the welding parameters and quickly adjust the modes via an intuitive menu. The advanced IGBT technology ensures high performance and an excellent duty cycle, while the ability to convert the machine into a TIG welder with an optional TIG welding torch provides additional versatility. This device is ideal for both experienced welders and beginners looking for a reliable and powerful solution. Flux-cored wire welding without shielding gas for versatile applications. Synergic wire feed for automated wire speed. Clear digital display for easy reading of welding parameters. Modern IGBT technology for high performance and efficiency. Optional conversion to a TIG welder with lift TIG function.
6. Stahlwerk Plasma cutter CUT 50 ST IGBT with 50 amps, up to 14mm cutting capacity
Properties
Plasma: conductive metals e.g. standard steel, copper, stainless steel, brass, aluminium, titanium can be cut without problems
Cutting capacity up to 14 mm (depending on material): mild steel ST37 up to 14mm / V2A or V4A up to 8 mm, - aluminium up to 5 mm
CUT contact: smooth-running HF ignition, one stroke is enough.
IGBT technology Advantages: powerful, good forward behaviour, high reverse voltage and robustness.
Technical Data
Output current: 15-50 A
Protection class: IP21S
Mains voltage: 1 x 230 V AC (+-15%)
Mains frequency: 50/60 Hz
Maximum mains current (I1max): 33 A
Maximum effective mains current (I1eff): 13,1 A
Weight: 7.2 kg
Dimensions L x W x H (mm): 390 x 170 x 275
Mains connection: CEE 7/7 Schuko plug
Air pressure: 3.5 - 4 bar
Air flow: min. 100 L / min
Standards: IEC 60974-1; EN 60974-10 (Class A)
Scope of delivery
1 x The CUT 50 ST steelwork plasma cutter
1 x professional plasma hose package AG-60/SG-55, 3 metres
1 x 3-piece plasma accessory set (this is already pre-assembled on the plasma torch):
1 x plasma nozzle
1 x plasma electrode
1 x ceramic cap
1 x earth cable 3 metres
1 x water separator with pressure gauge and snap-on quick-release couplings
1 x Connecting hose with snap-on quick-release couplings from the appliance to the water separator, incl. 6-piece connection set
1 x Air connection hose with Snap-on quick-release coupling 5m
1 x protective cover
1 x Teflon tape
Welding machines
CHF169.–
Stahlwerk Plasma cutter CUT 50 ST IGBT with 50 amps, up to 14mm cutting capacity
7. Stahlwerk Plasma cutter CUT 50 Pilot IGBT with pilot ignition and 50 amps
Properties
Plasma: conductive metals e.g. standard steel, copper, stainless steel, brass, aluminium, titanium can be cut without problems.
Cutting capacity up to 14 mm (depending on material): mild steel ST37 up to 14 mm / V2A or V4A up to 8 mm, - aluminium up to 5 mm
CUT Pilot: smooth-running HF pilot ignition, no contact necessary.
IGBT technology Advantages: powerful, good forward behaviour, high reverse voltage and robustness.
Fast cooling fan enables maximum power to be utilised and increases the duty cycle (ED) of the device.
Technical data
Output current: 15-50 A
Protection class: IP21S
Mains voltage: 1 x 230 V AC (+-15%)
Mains frequency: 50/60 Hz
Maximum mains current (I1max): 33 A
Maximum effective mains current (I1eff): 13,1 A
Weight: 8 kg
Dimensions L x W x H (mm): 390 x 170 x 275
Mains connection: CEE 7/7 Schuko plug
Air pressure: 3.5 - 4 bar
Air flow: min. 100 L / min
Standards: IEC 60974-1; EN 60974-10 (Class A)
Scope of delivery
1 x The CUT 50 P steelwork plasma cutter
1 x Professional plasma hose package P-60 3 metres
1 x 4-piece plasma accessory set (already pre-assembled on the plasma torch):
1 x plasma nozzle
1 x plasma electrode
1 x ceramic cap
1 x spacer
1 x 3 metre earth cable
1 x water separator with pressure gauge and snap-on quick-release couplings from the appliance to the water separator, incl. 6-piece connection set
1 x Air connection hose with snap-on quick coupling 5 metres
1 x protective cover
1 x Teflon tape
8. Stahlwerk DC TIG 200 ST IGBT welding machine with 200 amps and MMA electric hand
Properties
DC TIG welding - direct current (DC). Welding of almost all metals, such as steel, stainless steel, copper, brass and many more. Note: Not suitable for aluminium - an AC/DC device is required for this.
2 in 1 combination device - TIG & MMA welding is possible up to 200 A.
Technical data
Output current (TIG / MMA): 10-200 A
Protection class: IP21S
Mains voltage: 1 x 230 V AC (+- 15%)
Mains frequency: 50/60 Hz
Maximum mains current (I1max) (TIG / MMA): 27.7 A / 39.7 A
Maximum effective mains current (I1eff) (TIG / MMA): 14.5 A / 13.5 A
Weight: 7.6 kg
Dimensions L x W x H (mm): 390 x 170 x 275
Mains connection: CEE 7/7 Schuko plug
Standards: IEC 60974-1; EN 60974-10 (Class A)
Scope of delivery
1 x The DC TIG 200 ST IGBT steelwork welding machine
1 x Professional TIG welding torch WP-26F / hose package 3 metres* with flexible torch head and kink protection on the gas connection
1 x TIG TIG accessory set 8 pieces:
3 x gas nozzles sizes: 5, 6, 7
1 x clamping sleeve size 1.6
1 x clamping sleeve housing size 1.6
2 x burner caps - one short and one long
1 x universal tungsten electrode
(*Pre-assembled accessories from the picture of the welding torch are part of the 8-piece set)
1 x earth cable 3 metres
1 x welding cable with electrode holder 3 metres
1 x wire brush
1 x slag hammer
1 x Quick coupling gas pressure reducer incl. O-seal
1 x Gas connection hose with quick coupling 5 metres
1 x protective cover
Welding machines
CHF379.–
Stahlwerk DC TIG 200 ST IGBT welding machine with 200 amps and MMA electric hand
9. Stahlwerk 4 in 1 combination welding machine CTM-250 ST with 200 A and 50 A plasma function
Technical data
Output current (TIG/MMA/MIG/CUT): TIG,MMA: 10-200A / MIG: 40-200A / CUT: 15-50A
Protection class: IP21S
Mains voltage: 1 x 230V AC (+- 15%)
Mains frequency: 50/60 Hz
Maximum mains current (l1max) (TIG/MMA/MIG/CUT): 26.8A / 41.7 A / 35.7 A/ 37.2A
Maximum effective mains current (l1err) (TIG/ MMA/MIG/ CUT): 10.4A I 13.2A I 13.8A I 14.4A
Air pressure CUT: max. 4Bar
Air flow CUT: min. 100L/min
Dimensions Lx W x H (mm): 440 X 255 X360
Scope of delivery
1 x The CTM-250 ST steelworks combi welding machine
1 x Professional TIG welding torch WP-26F / hose package 3 metres
1 x TIG TIG accessory set 8 pieces
1 x Professional plasma hose package AG-60/SG-55 3 metres
1 x Plasma accessory set 3-piece (this is already pre-assembled on the plasma torch)
1 x water separator with pressure gauge and snap-on quick couplings
1 x connecting hose with snap-on quick-release couplings from the device to the water separator, incl. 6-piece connection set
1 x AK-15 professional MIG welding torch / 3 metre hose package with Euro central connection
1 x 3-piece MIG accessory set (this is already pre-assembled on the MIG/MAG torch): 1 x gas nozzle, 1 x contact tip 0.8 mm, 1 x gas nozzle holder
1 x earth cable 3 metres
1 x electrode holder 3 metres
1 x wire brush
1 x gas connection hose with quick coupling 5 metres
1 x contact tip M6 x 28 - ø 0.8 mm
1 x contact tip M6 x 28 - ø 1.0 mm
2 x wire guide rollers 0.8 mm & 1.0 mm with V profile (already installed in the device)
2 x wire guide roller 0.6 mm & 0.8 mm with V profile
1 x assembly spanner
1 x Teflon tape
1 x protective cover
Welding machines
CHF681.–
Stahlwerk 4 in 1 combination welding machine CTM-250 ST with 200 A and 50 A plasma function
10. Stahlwerk Shielded arc welder AC/DC TIG 200 Puls Pro Touch
Model: AC/DC TIG 200 Pulse Pro Touch welding machine. Output current (TIG / MMA): 5 - 200 A / 30 - 160 A. TIG duty cycle (40°C): 25% at 200 A / 60% at 150 A / 100% at 120 A. MMA duty cycle (40°C): 25% at 160 A / 60% at 110 A / 100% at 90 A. TIG AC duty cycle (40°C): 25% at 200 A / 60% at 150 A / 100% at 120 A. Protection class: IP21S. Mains voltage: 1 x 230 V AC. Mains frequency: 50 Hz. Open circuit voltage (TIG DC and MMA / TIG AC): 68 V / 48 V. Maximum mains current (I1max) | (TIG / MMA): 28 A. Maximum effective mains current (I1eff) | (TIG / MMA): 15.6 A. Weight: 17.5 kg. Dimensions L x W x H (mm): 450 x 245 x 430. Mains connection: CEE 7/7 Schuko plug. Standards: IEC 60974-1; EN 60974-10 (Class A). Certified by: TÜV Rheinland. Scope of delivery: 1 x steelworks AC/DC TIG 200 Puls Pro Touch welding machine. 1 x Professional TIG welding torch "WP-26 FR". 1 x TIG TIG accessory set 8-piece: 3 x gas nozzles sizes: 5, 6, 7. 1 x clamping sleeve size 1.6. 1 x clamping sleeve housing size 1.6. 2 x torch caps - one short and one long. 1 x universal tungsten electrode 1.6 mm. * Pre-assembled accessories from the illustration of the welding torch are included in the 8-piece set. 1 x gas connection hose with quick coupling 5 m. 1 x earth clamp 3 m cable with 13 mm pin plug. 1 x quick coupling gas pressure reducer. 1 x TIG welding rods ER70S G3 steel. 1 x welding rods TIG ER307Si high-alloy stainless steel. 1 x TIG welding rods ER4043Si5 high-alloy aluminium. 1 x tungsten electrodes / welding electrodes. 1 x TIG foot pedal Puls Pro with 4 m cable. 1 x slag hammer. 1 x wire brush. 1 x protective cover. 1 x pressure reducer. 1 x Professional welding helmet.
