Best selling Energy monitors from Eltako
This page always stays fresh and updates automatically.
1. Eltako Three-phase meter
Eltako Mobile Three-Phase Meter DSZ180CEE-16
Manufacturer: Eltako
Description: Mobile three-phase meter MID calibrated 16A
Type: DSZ180CEE-16
Meter type: electronic
Rated current (In): 10 A
Maximum current (Imax): 80 A
Rated voltage (Un) N-L: 230 V
Rated voltage (Un) L-L: 400 V
Frequency: 50 Hz
Accuracy class: B
Connection type: four-wire
Design: direct measurement
Energy type: active power
Suitable for: consumption
Reverse flow prevention: yes
Calibrated: yes
Approval: Measuring Instruments Directive
Display type: digital
Width: 86 mm
Depth: 82 mm
Height: 180 mm
Interface design: other
Number of digits: 7
Protection class (IP): IP54
Additional details: Mobile three-phase meter with CEE plug 16A and CEE socket 16A. Suitable for indoor and outdoor use. Maximum current 16A, standby loss only 0.5 watts per path. Housing dimensions 180 x 86 x 82 mm, connection cable 1.5 m (including plug and socket). Accuracy class B (1%). This mobile three-phase meter measures active energy based on the currents flowing between the inputs and outputs. The self-consumption of a maximum of only 0.5 watts of active power per path is not measured and not displayed. The starting current is 40 mA. The display can only be read when powered. However, the consumption is non-volatile stored and is immediately displayed again after a power failure. The digital display has 7 digits. Up to 99999.99 kWh, two decimal places are displayed; from 100000.0 kWh, only one decimal place is shown. The power consumption is indicated by a bar that blinks 100 times per kWh on the display. EAN: 4010312501863.
2. Eltako DSZ15EN
Maximum current 3x80A, standby loss only 0.5 watts per path. Modular device for mounting on DIN rail EN 60715 TH35. 4 division units = 70 mm wide, 58 mm deep. Accuracy class B (1%). With S0 interface. The directly measuring three-phase energy meter measures active energy based on the currents flowing between the inputs and outputs. The self-consumption of only a maximum of 0.5 watts active power per path is not measured and not displayed. 1, 2, or 3 external conductors with currents up to 80A can be connected. The starting current is 40 mA. The neutral connection must be present. The 7-segment LC display can also be read twice within two weeks without power supply. The power consumption is indicated by a bar that blinks 100 times per kWh on the display. It can also be used as a 2-tariff meter as standard: applying 230V to terminals E1/E2 switches to a second tariff. To the right of the display are the MODE and SELECT buttons.
What our customers think
Pro
- Illuminated display
- Quick installation
3. Eltako Alternating current meter
Only calibrated meters are approved for electricity billing according to §25 of the German Calibration Act. Non-compliance is an administrative offense under §19. Maximum current is 32A, with a standby loss of only 0.4 watts. This is a modular device for mounting on DIN-EN 60715 TH35 mounting rails. 1 division unit = 18mm wide, 58mm deep. Accuracy class B (1%). With S0 interface. This alternating current meter measures active energy based on the current flowing between the input and output. The self-consumption of only a maximum of 0.4 watts of active power is not measured and not displayed. One external conductor with a current of up to 32A can be connected. The starting current is 20mA. If a load of more than 50% is expected, a ventilation distance of 1/2 division unit must be maintained from adjacent mounted devices. If necessary, use the spacer DS12. Two N terminals for secure cross-wiring of multiple meters. The 7-segment LC display can also be shown twice within two seconds without power supply.
4. Eltako Energy meter
Mobile three-phase energy meter with CEE plug 32A and CEE socket 32A. Suitable for indoor and outdoor use. Maximum current 32 A, standby loss only 0.5 watts per path. Housing dimensions 180 x 86 x 82 mm, connection cable 1.5 m (including plug and socket). Accuracy class B (1%). This mobile three-phase energy meter measures active energy based on the current between input and output. The internal power consumption of max. 0.5 watts active power per path is neither measured nor displayed. The inrush current is 40 mA. The display is only readable when the power supply is on. However, the consumption is stored non-volatile and immediately displayed after a power failure. The digital display is 7 digits. Up to 99999.99 kWh, two decimal places are shown. Above 100,000.0 kWh, only one decimal place is displayed. The power consumption is indicated by the LED blinking 100 times per kWh.
5. Eltako MOBILE A.C. Z. MID GEE (WSZ155DSS-16A)
Mobile AC power meter with protective contact plug and socket. Suitable for indoor and outdoor use. Maximum current 16 A. Protection class IP54. Standby loss is only 0.4 watts. Housing dimensions are 155 x 60 x 82 mm, connection cable 1.5 m (including plug and socket). Accuracy class B (1%). This mobile AC power meter measures active energy based on the current flowing between the input and output. The self-consumption of only a maximum of 0.4 watts of active power is not measured or displayed. The display cyclically alternates every 10 seconds between the accumulated active energy in kWh and the current consumption in kW. The starting current is 20 mA. The display can only be read when powered. However, the consumption is stored non-volatile and is immediately displayed again after a power outage. The digital display has 7 digits. Up to 99999.99 kWh, two decimal places are shown; from 100000.0 kWh onwards, only one decimal place is displayed. The mobile AC power meter is equipped with a mounting bracket for easy installation, which can be easily removed if not needed. Power consumption is indicated by a LED that blinks 2000 times per kWh.
6. Eltako ELTA Mode electricity meter
Gateway with IP interface via WLAN or LAN. Standby loss is only 0.9 watts. Rail-mounted device for installation on DIN-EN 60715 TH35 mounting rail. 2 division units = 36 mm wide, 58 mm deep. The WLAN connection uses the 2.4 GHz frequency band. The LAN connection is made via RJ45 connector with 10/100Base-T. The IP connection is established via LAN or WLAN. The gateway transmits data from any ELTAKO Modbus power meters using the MQTT protocol and REST API. Data is transferred from the ZGW16WL-IP to any external MQTT broker. Commissioning and viewing the current meter values as well as the history are possible through both the ELTAKO Connect app and the web interface. The web interface also allows for easy configuration and updates. A REST API is available on the device's online product page.
7. Eltako DSZ15WD-3X5A MID
Only calibrated meters are approved for electricity billing according to §25 of the German Calibration Act. Non-compliance is considered an administrative offense under §19. This is a transformer three-phase meter with adjustable transformer ratio and MID. Maximum current is 3x5A, with a standby loss of only 0.5 watts per path. It is a modular device for mounting on a DIN-EN 60715 TH35 rail. It occupies 4 division units = 70mm wide, 58mm deep. Accuracy class B (1%). Equipped with an S0 interface. This three-phase meter measures active energy based on the currents flowing through the transformers. The self-consumption of only a maximum of 0.5 watts active power per path is not measured or displayed. It can connect 1, 2, or 3 transformers with secondary currents up to 5A. The starting current is 10mA. The neutral connection must be present. The 7-segment LC display can also be read twice within two weeks without power supply. The power consumption is indicated by a bar that blinks 10 times per kWh on the display.
8. Eltako usRadio three-phase meter MID calibrated
Only calibrated meters are approved for electricity billing according to §25 of the German Calibration Act. Non-compliance is an administrative offense under §19. RS485 bus radio three-phase meter. Maximum current 3x80A, standby loss only 0.8 watts on L1 and 0.5 watts each on L2 and L3. Accuracy class B (1%). With RS485 interface. The directly measuring three-phase meter measures the active energy based on the currents flowing between the inputs and outputs. The self-consumption of only a maximum of 0.8 watts or 0.5 watts active power per path is not measured and not displayed. 1, 2, or 3 external conductors with currents up to 80A can be connected. The starting current is 40 mA. Connections L1 and N must be present. Connection via an FBA14 to the Eltako RS485 bus with a 2-wire shielded bus line (e.g., telephone line). The meter reading and instantaneous power are transmitted to the bus - e.g., for forwarding to an external computer or the GFVS 3.0 software - and also via the FAM14 into the radio.
9. Eltako FGW14W-IP Gateway Top-hat rail
Eltako BUS Power Meter FGW14W-IP
Manufacturer: Eltako
Designation: BUS Power Meter
Type: FGW14W-IP
KNX Bus System: no
KNX Radio Bus System: no
Radio Bus System: yes
LON Bus System: no
Powernet Bus System: no
Other Bus Systems: none
Bidirectional Radio: no
Design: RS-485
Mounting Type: DIN Rail
Width in Division Units: 1
Disassembly Protection: no
With LED Display: no
Updatable: no
Operating Voltage: 12 V
Voltage Type: DC
Power Consumption: 0.8 W
Protocol: other
Provider Dependent: no
Visualization: no
Web Server: no
Radio Interface: no
IR Interface: no
Protection Class (IP): IP20
The gateway with IP interface for the series 14 power meters via WLAN has a standby loss of only 0.8 watts. It is a modular device designed for mounting on DIN rail EN 60715 TH35. One division unit corresponds to 18 mm in width and 58 mm in depth. The gateway is only 1 division unit wide. To operate, the gateway must be integrated into a WLAN that uses the 2.4 GHz frequency band. Connection is made to the Eltako RS485 bus. Cross-wiring of the bus and power supply is done with a jumper. Operation is possible in conjunction with FAM14 or FTS14KS. The hold terminal is connected to the FAM14 or FTS14KS. The IP connection is established via WLAN. The gateway transmits data from any Eltako power meters on the RS485 bus to an external MQTT broker using the MQTT protocol. The data is encoded according to the EnOcean over IP format. Configurations and updates are carried out via the Eltako Connect app or through a web interface. A REST API is available via the online product page of the device.
EAN: 4010312327876.
10. Eltako MBusWandlerThree-phase meter MID calibrated
Only calibrated meters are approved for electricity billing according to §25 of the German Calibration Act. Non-compliance is an administrative offense under §19. M-Bus converter three-phase meter with adjustable converter ratio and MID. Maximum current 3x5A, standby loss only 0.5 watts per path. Rail-mounted device for installation on DIN-EN 60715 TH35 mounting rail. 4 division units = 70 mm wide, 58 mm deep. Accuracy class B (1%). With M-Bus interface. This three-phase meter measures active energy based on the currents flowing through the converters. The self-consumption of only a maximum of 0.5 watts active power per path is not measured and not displayed. 1, 2, or 3 converters can be connected with secondary currents up to 5A. The starting current is 10 mA. The neutral connection must be present. The 7-segment LC display can also be read twice within two weeks without power supply. The power consumption is indicated by a LED that blinks 10 times per kWh. To the right of the display is...
Product order
See all products