Best products in the Floor heating category
Here's a ranking of the best products in this category. To give you a quick overview, we've also added some key information about the products.
1. Devi To establish a 088U1101 WLAN connection App module
Devi App module 088U1101 Manufacturer :Devi Designation :App module for WLAN connection Type :088U1101 Type of accessory/spare part :other Devi App module 088U1101: more details For establishing a WLAN connection to the router, for using time schedules (comfort and setback phases) and for remote control of pernSmartphone via the Danfoss Icon¿ App , EAN: 5702425147104.
2. Honeywell Thermal drive de-energised
The actuator can be mounted easily and in any installation position without tools. Due to its compact design, it is also suitable for tight installation spaces. These actuators can be used for time-controlled two-point and pulse-width modulated control of floor heating systems.
3. Devi Thin-bed heating mat set 140F0822 1-600 W professional DTIF 4,0qm 50x80
Devi Thin-bed set 1-600 W 140F0822 Manufacturer :Devi Designation :Thin-bed set 1-600 W DTIF 4,0 qm,professi Type :140F0822 With support mat :yes Fixation of the heating conductor :Glued Self-adhesive :yes Connected load :0..600 W Output :150 W/m² Heatsealing band load :11 W/m Number of PTC thermistors :1 Length of PTC thermistors :4000 mm Suitable for damp rooms :yes Suitable as open space heating :no Suitable as roof surface heating :no Area :4 m² Length :8000 mm Width :500 mm Thickness :3,5 mm With controller :yes With room thermostat :yes With floor temperature sensor :yes Devi thin-bed set 1-600 W 140F0822: more details Thin-bed set with touch thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, installation instructions. The self-adhesive thin-bed heating mat with a connection cable is ready to install and has been specially developed for installation in levelling compound or flexible adhesive directly underneath the floor covering. Due to the low installation height of only 3.2 mm, it is ideal for the renovation and modernisation of bathrooms, showers, kitchens, etc. This floor temperature control system is particularly suitable for retrofitting in rooms with many nooks and crannies and/or large rooms, as there is no need to lead back the second connection. The heating cable with additional protective braiding for the use of the FI protection circuit, is mounted on a plastic net. The length of the connection cables is 4.0 m. PTC resistor: 1 x 4m, 1.0mm², voltage: 230 V, nominal limit temperature: 120°C, specific heat output: 150 W/m², linear load: 11W, insulation: PVDF / FEP, resistance tolerance: +10% / -5%, minimum laying temperature:5°C, Smallest bending radius: 6 x dA, Calculation width 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval : EN 60335-2-96, Area 4.0 m², 0.5 x 8.0 m , EAN: 5703466216569.
4. Devi Thin-bed heating mat set 140F0818 1-300 W professional DTIF 2,0qm 50x40
Devi Thin-bed set 1-300 W 140F0818 Manufacturer :Devi Designation :Thin-bed set 1-300 W DTIF 2,0 qm,professi Type :140F0818 With support mat :yes Fixation of the heating conductor :Glued Self-adhesive :yes Connected load :0..300 W Output :150 W/m² Heatsealing band load :11 W/m Number of PTC thermistors :1 Length of PTC thermistors :4000 mm Suitable for damp rooms :yes Suitable as open space heating :no Suitable as roof surface heating :no Area :2 m² Length :4000 mm Width :500 mm Thickness :3,5 mm With controller :yes With room thermostat :yes With floor temperature sensor :yes Devi thin-bed set 1-300 W 140F0818: more details Thin-bed set with touch thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, installation instructions. The self-adhesive thin-bed heating mat with a connection cable is ready to install and has been specially developed for installation in levelling compound or flexible adhesive directly underneath the floor covering. Due to the low installation height of only 3.2 mm, it is ideal for the renovation and modernisation of bathrooms, showers, kitchens, etc. This floor temperature control system is particularly suitable for retrofitting in rooms with many nooks and crannies and/or large rooms, as there is no need to lead back the second connection. The heating cable with additional protective braiding for the use of the FI protection circuit, is mounted on a plastic net. The length of the connection cables is 4.0 m. PTC resistor: 1 x 4m, 1.0mm², voltage: 230 V, nominal limit temperature: 120°C, specific heat output: 150 W/m², linear load: 11W, insulation: PVDF / FEP, resistance tolerance: +10% / -5%, minimum laying temperature:5°C, Smallest bending radius: 6 x dA, Calculation width 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval : EN 60335-2-96, Area 2.0 m², 0.5 x 4.0 m , EAN: 5703466216521.
5. Stiebel Eltron FTM 200/2
Stiebel Eltron Floor temperature control FTM 200/2 Manufacturer :Stiebel Eltron Designation :Floor temperature control 2 sqm, 400W/230V Type :FTM 200/2 Design :Heating cable With support mat :yes Fixation of the heating conductor :sewn Self-adhesive :yes Supply voltage :230 V Connected load :400 W Output :200 W/m² Heating conductor load :10 W/m Resistance :128 Ohm Number of PTC thermistors :1 Length of PTC thermistors :4000 mm Suitable for damp rooms :yes Suitable as outdoor heating :no Suitable as roof heating :no Area :2 m² Length :6700 mm Width :300 mm Thickness :3 mm With controller :no With room thermostat :no With floor temperature sensor :no Stiebel Eltron floor temperature control FTM 200/2: more details The thin-bed heating mats with high heating output are used in new buildings and renovations for floor temperature control, especially in bathrooms. They are installed directly under the floor covering and quickly provide a pleasantly warm floor surface, independent of the existing heating system. The heating mat is suitable as additional or supplementary heating. COMFORT FEATURES: Due to the low installation height, the heating mat can be installed directly in the tile adhesive under ceramic coverings. The smaller installation width is particularly suitable for small, angled floor plans. In combination with a water-guided underfloor heating system, the comfort of a warm floor can thus also be made possible outside the heating season. The heating conductor is completely sewn onto the self-adhesive support mat and can therefore be laid quickly and easily on the floor. INSTALLATION: The mat may be laid in the bathroom in conjunction with a residual current circuit breaker. By cutting the backing fabric to size, the mats can be easily adapted to the individual space conditions. , EAN: 4017212057117.
6. Stiebel Eltron FTM 200/0.6
Stiebel Eltron Floor temperature control FTB 200/0.6 Manufacturer :Stiebel Eltron Designation :Floor temperature control 0.6 sqm, 120W/230V Type :FTB 200/0.6 Design :Heating cable With support mat :yes Fixing of heating conductor :sewn Self-adhesive :yes Connected voltage :230 V Connected load :120 W Output :200 W/m² Heating conductor load :10 W/m Resistance :441 Ohm Number of PTC thermistors :1 Length of PTC thermistors :4000 mm Suitable for damp rooms :yes Suitable as outdoor heating :no Suitable as roof heating :no Area :0.6 m² Length :1600 mm Width :400 mm Thickness :3 mm With controller :no With room thermostat :no With floor temperature sensor :no Stiebel Eltron floor temperature control FTB 200/0.6: further details The heating mats are used for temperature control of the floor in wet areas. They are suitable for both new buildings and renovations. The heating mats are installed directly under the floor covering and quickly provide a pleasantly warm floor surface. COMFORT FEATURES: Ideal for wellness areas, tiled shower trays, relaxation loungers, benches or whirlpool surrounds. Due to the low installation height, it can be used in tile adhesive under ceramic coverings. Small heating conductor spacing for even heating, especially of small-format tiles and mosaics. High-quality heating conductors with FEP insulation. INSTALLATION: In conjunction with a residual-current device, the mat may be installed in wet areas under protection zone 0. , EAN: 4017212057230.
7. Danfoss VERIA QM 100 900W 230V 9M*2
Danfoss Veria QM 100. Poids: 4,49 kg. Type de produit: Chauffage par le sol électrique, Code (IP) Internationale Protection: IPX7. Puissance: 900 W, Tension d'entrée AC: 230 V. Poids du paquet: 4,53 kg.
8. Danfoss ECmat 200T 215W 230V 0.5x2.1m
ECmat 200T 215W 230V 0.5x2.1m.
9. Devi Thin-bed set 300 W, 2.0qm 140F1652 with WLAN thermostat
Danfoss 140F1652 Thin bed set 300W.
10. Danfoss Electric Floor Heating ECmat
Danfoss ECmat 100T. Peso: 2,25 kg. Tipo di prodotto: Riscaldamento elettrico a pavimento, Larghezza del cavo di riscaldamento: 3 mm, Schermatura dei cavi: Foglio di alluminio Mylar. Potenza: 300 W, Tensione di ingresso AC: 230 V. Peso dell'imballo: 2,23 kg.
