Questions about Pioneer SPH-DA360DAB

Yes, it is compatible with the corresponding adapters and the corresponding covers for installation, and there is also an adapter set for any steering wheel controls

I haven't tried it, but it shouldn't be a problem, there is only one mono output.

Yes, you can use the speaker outputs of the internal amplifier (for the speakers) at the same time as the pre-out connections (for the subwoofer). The device has 3 pre-amplifier outputs (front, rear, subwoofer) and an internal 4x50W MOSFET amplifier, which enables parallel use. According to the technical specifications, no additional amplifier is required for the speakers - these can be connected directly to the radio, while the subwoofer is operated via the RCA pre-outs with an external amplifier. *Note:* The pre-outs are intended exclusively for connecting external amplifiers, while the speakers can be connected directly to the radio. A combination of both connection types is possible without any problems.

Hai installato il can bus?

Forgotten the blue AMP cable? This must be connected for the amplifier to switch on.

The device is a 2-DIN car radio, which means that it fits into most vehicles with a 2-DIN slot. Whether it fits specifically in your Seat Exeo ST depends on the dimensions of the radio slot in your vehicle. You should check the dimensions to make sure it fits. The DAB+ antenna is optional and is not supplied as standard. You can purchase the CA-AN-DAB.001 antenna separately to utilise DAB+ functionality.

Hello, for your aerial you can use this Blaupunkt DAB-S-22A device which allows Dab+ reception with an FM/AM aerial without installing additional antennas (make sure, however, that your aerial is not amplified otherwise it will not work properly). To keep the steering wheel controls, you need a Can-bus adapter for Mazda, which is not available on Galaxus.

Yes I mounted it works fine you have to put a canbus and chassis adapter

With an appropriate radio panel and the right adapter plugs, it should work. However, if the Mito still has steering wheel controls and sat nav, I would leave the replacement to a specialist (in this case, you would need the right interface modules and control units). In my Zafira, I also had the specialist do it, but my DAB aerial and the PGS module were neatly installed behind the panelling. Usually takes about 3-4 hours.

To install the car radio in a Peugeot 207 CV, you need to make sure that the radio is the right size and is compatible. The SPH-DA360DAB is a 2-DIN device, which means that it fits into most 2-DIN slots. However, compatibility may vary depending on the vehicle model and equipment. It is advisable to check the specific requirements of your vehicle and, if necessary, consult a professional to ensure that the device is installed correctly.

https://www.autoscout24.it/annunci/suzuki-swift-5p-1-3-diesel-75cv-neopatentato-diesel-grigio-28eaee76-90a5-4d74-a3d5-796cace9aaac?sort=standard&desc=0&lastSeenGuidPresent=false&cldtidx=1&position=1&search_id=452wqiixp3&source_otp=t50&ap_tier=t50&source=listpage_search-results&order_bucket=6&new_taxonomy_available=false&mia_tier=t50&boosting_product=mia&relevance_adjustment=boost&applied_mia_tier=t50

The Pioneer SPH-DA360DAB car radio can be installed in a 2012 Mercedes Vito W639, but it requires some precautions and possibly additional components. - The car radio is a 2-DIN model, which is compatible with the standard dimensions of the Vito W639. - However, it is important that you use the correct adapters and cable kits for installation in your specific vehicle model. These kits should allow control of the steering wheel controls, connection to any reversing cameras and other vehicle systems. - Professional installation or careful planning is recommended to ensure that all functions are integrated correctly. Before installation, you should therefore carefully check the necessary adapters and instructions and seek professional help if necessary.

First things first, via USB or WiFi ? Did you read the manual ? (RTFM)

Yes, you still need various material I still needed Radio cover Can Bus adapter that the remote control from the steering wheel worked again I have changed the antenna for dab but there are also adhesive antennas I have mounted a combination antenna with dab fm and gps With the antenna there are adapters for dan but does not work with every antenna

You need to look at the dimensions of your car, but I think so.

To determine if the Pioneer SPH-DA360DAB can be installed in a 2014 Range Rover Sport, you need to consider a few factors: ## Compatibility - The SPH-DA360DAB is a 2-Din unit, which means it is designed to fit into a standard 2-Din car stereo slot. You need to check if your 2014 Range Rover Sport has a compatible 2-Din slot or if any modifications would be required. ## Electrical and Mechanical Integration - Ensure that the electrical connections and wiring of the SPH-DA360DAB are compatible with your vehicle's system. This may involve checking the wiring harness and any specific connectors required for the Range Rover Sport. - You may also need to consider the steering wheel controls, reverse camera integration, and any other vehicle-specific features that need to be integrated with the new head unit. ## Additional Components - The installation might require additional components such as a wiring adapter, steering wheel control interface, or a reverse camera adapter to ensure full functionality. ## Professional Installation - Given the complexity of modern vehicle electronics, it is highly recommended to consult a professional auto electrician or a car audio specialist who has experience with installations in your specific vehicle model. Before proceeding, it would be wise to consult the manufacturer's installation guide, the vehicle's manual, or contact a professional installer to ensure a smooth and compatible installation.

With the correct plug adapter, the original plugs fit and the steering wheel remote control works. The rest must be fitted separately. This includes the microphone, GPS antenna (included), DAB+ antenna (not included) and reversing camera (not included). If you had a transmitter or music display in the speedometer area, this will no longer work either.

The Pioneer SPH-DA360DAB car radio can be installed in a 2014 Toyota Verso, but there are a few things to consider: - Compatibility: the car radio itself is compatible with most vehicles, but the physical fit and electrical connections need to be checked. - Bezel and mounting kit: To install the car radio in the 2014 Toyota Verso, a specific mounting kit and a matching bezel are usually required. These kits are usually available from third-party suppliers such as Metra, Scosche or other manufacturers and must be selected specifically for the model of the vehicle and the car radio. - Electrical connections: It is also important to ensure that the car radio's electrical connections are compatible with those of the vehicle. This may require special adapters or looms. It is recommended to consult a professional before installation or clarify the specific requirements and compatibility details with the mounting kit and panel manufacturer.

Working fine here - have you made sure the hand brake signal is connected properly with the can Bus? That's just my obvious first thought, hope you get it to work!