Best selling Battery accessories from Victron Energy
On this page you'll find a ranking of the best Victron Energy products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.
1. Victron Energy Bus bar VBB115060020 Mounting plate
The busbar connecting rail reduces the cable required for the parallel mounting of several modular fuse holders, thus facilitating the installation.
2. Victron Energy SolidSwitch 104
Solid Switch 104
The SolidSwitch 104 switches DC loads of up to 70V/4A. It can be controlled by a low power digital signal (greater than 3.3V, greater than 30uA). The DC load can be resistive, capacitive, or inductive (for example, the coil of a high-power contactor). The SolidSwitch is not protected against polarity reversal and is not short-circuit proof.
It is used for load and charge disconnection in lithium BMS. It is also ideal for switching off your light engine by interrupting the excitation voltage.
3. Victron Energy Smart Battery Protect 12/24V--220A BPR122022000 Battery Isolator
The Victron Battery-Protect BP-220 disconnects the battery from less important consumers before it is fully discharged, which could cause damage, or before it no longer has enough energy to start the engine. Additionally, the BP series features overvoltage protection, which disconnects the load at 16 V or 32 V battery voltage, safeguarding against damage. The BP supports AGM, lead-acid, gel, and lithium batteries.
Six different disconnect thresholds are adjustable. The Battery-Protect is highly flexible and can be set to various disconnect voltages. The following disconnect thresholds can be activated on the device: 10.5 V / 21 V, 10 V / 20 V, 9.5 V / 19 V, 11.25 V / 22.5 V, 11.5 V / 23 V, 11.8 V / 23.6 V. Additionally, there are different reconnection thresholds available for most disconnect thresholds. This makes the device the perfect protection for your battery, ensuring maximum lifespan, as most voltage converters or charge controllers do have undervoltage protection, but this typically activates at quite low values, usually around 10.5 V / 21 V. The higher the disconnect threshold, the longer you will enjoy your batteries, which are generally quite costly.
The selection of the disconnect threshold depends on the battery type, as different minimum battery voltages must be adhered to in order to avoid damaging the battery.
Battery accessories
−7%
CHF84.– was CHF90.–
Victron Energy Smart Battery Protect 12/24V--220A BPR122022000 Battery Isolator
4. Victron Energy Smart Battery Protect 12/24V-100A BPR110022000 Battery Isolator
The Smart BatteryProtect disconnects the battery from less important consumers before it is completely discharged, which could cause damage, or before it no longer has enough energy to start the engine.
Battery accessories
CHF60.–
Victron Energy Smart Battery Protect 12/24V-100A BPR110022000 Battery Isolator
5. Victron Energy Lynx Shunt VE.Can
Lynx Shunt VE.Can
The Lynx Shunt VE.Can includes a positive and negative busbar, a battery monitor, and a fuse holder for the system's main fuse. With the built-in battery monitor, the state of charge of the battery can be accurately monitored. The Lynx Shunt VE.Can can communicate with a GX device via VE.Can or be connected to a chart plotter via NMEA2000, where the battery data will be displayed. It is part of the modular Lynx distribution system and can only be programmed through a GX device.
6. Victron Energy RJ12 UTP BMV ASS030066009 Connecting cable
This Victron RJ12 UTP cable (MPN ASS030066003) is required to connect a BMV shunt to the BMV monitor. Typically, an RJ12 cable is included with the BMV monitor, but if it is too short or too long, you can replace it with this cable.
Product features:
- Connector type: RJ12 on both ends
- Length: 0.9 meters
Delivery includes:
1x Victron RJ12 UTP cable 0.9 meters.
7. Victron Energy Plug Victron MagCode Power Port 12 V (max. 15A)
Connection box suitable for IP65 Blue Smart chargers
- Connects the charger to the battery in a vehicle
- Contacts are held together by magnets
- Connection is separated under tension
- Suitable for IP65 Blue Smart chargers.
8. Victron Energy Active GPS antenna Victron
The active GPS antenna from Victron Energy serves as an accessory for the GX GSM modem. Current location and movement speed can be provided via the active GPS antenna.
9. Victron Energy Shunt 2000A/50mV without board
The Victron Shunt 2000A - 50mV (MPN SHU202050200) is required for current measuring devices with analog or digital display instruments, as these typically operate by measuring a very small voltage across a shunt. In the case of Victron shunts rated from 1000A to 6000A, the measurement voltage is 50mV. The principle is: the smaller the measurement voltage across the shunts, the lesser the impact on the remaining circuit of the system. With 50mV, this shunt provides an excellent value.
The shunt is installed in the line carrying the current to be measured. The small voltage drop across this resistor is evaluated with a measuring device such as the Victron Battery Monitor BMV 700 to derive and display values like the current flow.
To determine whether you need a shunt for your display device, please refer to the manual of the respective device.
Package includes: 1x Victron SHU202050200 Shunt 2000A - 50mV.
10. Victron Energy Shunt SHU500050100 Battery monitoring
The Victron Energy Shunt SHU500050100 is a high-quality accessory for battery monitoring that enables precise measurement of current flow in battery systems. With a maximum current of 500A and a voltage of 50mV, this shunt provides a reliable solution for monitoring and managing battery performance. It is particularly useful in applications where accurate monitoring of energy consumption and battery performance is required. The shunt is suitable for use in various battery systems and contributes to optimising energy efficiency. Its robust construction ensures a long lifespan and reliability, while the straightforward installation allows for quick integration into existing systems. The Victron Energy Shunt is therefore a valuable addition for anyone looking to effectively monitor their battery performance.
- Maximum current of 500A for precise measurements
- Voltage of 50mV for enhanced accuracy
- Robust construction for a long lifespan.
