CHF57.90
Philips Hue Wandschalter Modul
Questions about Philips Hue Wandschalter Modul
What would you like to know?
0 questions and answers
Former employee
4 years ago
Since a set price does not automatically adjust to the individual prices, it may happen that the set price is higher after a reduction of the individual price than if the individual items were ordered separately.
Former employee
4 years ago
Yes, you need to remove the initial switch, disconnect it from the power supply, attach the Philips system instead, connect it to the switch and put it back on as before. (The HUE system is then located between the electrical connection and your switch.
If needed, Philips has videos on their website explaining how to do this. :)
Helpful answer
No, this has a battery.
If the two wires from the module are short-circuited via a connected wall switch contact, there is a Hue signal.
I do not recommend exposing these wires to a voltage of 230V as the insulation is not suitable for this.
The 230V wires previously switched with the switch must be short-circuited so that there is continuous voltage on the lamp.
In terms of safety, this intervention in the electrical installation should be carried out by a licenced specialist, as is the case with any lamp installation. So that this is also mentioned.
Helpful answer
https://www.smartlights.de/news/faq-eure-fragen-antworten-zum-philips-hue-wandschaltermodul-das-muesst-ihr-wissen/#wie-lange-halt-die-cr2045-batterie-im-philips-hue-wandschalter-modul-und-wie-tausche-ich-sie-aus
Galaxus
1 month ago
The Philips Hue wall switch module is specially designed to control smart Philips Hue lamps, rooms or zones by installing it behind an existing light switch. It enables switching on and off as well as switching through up to three light scenes via the switch. This module is not intended to control blinds (shutters) as it is only designed for light control in the Philips Hue system.
Automatically generated from the .
Hello
You need to reset the module and select push-button rather than rocker at the beginning of the installation.
Galaxus
7 months ago
Helpful answer
The wall switch module is installed behind the existing light switch and makes it smart-enabled without replacing the switch itself. It acts as an interface between the physical switch and the Hue Bridge by converting the switching commands of the original switch into smart commands.
How it works in detail:
- Installation: The module is installed in the flush-mounted box behind the light switch. The power supply to the lamp is switched to continuous current (e.g. with a Wago terminal) so that Hue lights are constantly supplied with power.
- Switch control: The original switch remains active, but no longer sends a power interruption to the lamp. Instead, the module recognises the switching operations and transmits them as a signal to the Hue Bridge.
- Scene control: Up to three light scenes can be configured per switch via the Hue app. These scenes are switched through by repeatedly pressing the switch (on/off).
- Push-button compatibility: When using a push-button (instead of a switch), the module also enables dimming by a long press.
The module is therefore not a separate switch, but uses the existing switch as an input device for Smart commands. The physical switch continues to control the module, which forwards the commands to the Hue Bridge.
Automatically generated from the .
The module has two independent channels. Several push-buttons (impulse push-buttons) can be connected per channel.
Helpful answer
Hello, I can answer the question myself. If you configure the wall switch module as a toggle switch then it works as desired. The switch is not a toggle switch but the behaviour seems to be the same :-).
Helpful answer
Yes, it works
Fibaro has products - but with zWave protocol which requires an additional gateway for use with HomeKit.
Fibaro also has a HomeKit only solution that uses Bluetooth, but this is then really only HomeKit.
Relay (on/off): Fibaro relay flush-mounted insert 2 switches
Dimmer: Fibaro universal dimmer 2 250W
I use the wall switch module with a Conbee II, so not with a Hue Bridge either. However, I don't know whether it actually works with the IKEA Hub.
Helpful answer
No and yes. The WSM is only connected to the physical switch. If this is activated, the WSM sends a zigbee command to the bridge. This then switches whatever is programmed. The motion detector does the same. The cables that were previously on the switch are bridged with a WAGO 221. The load is therefore always on. Of course, you can use the WSM in parallel with the motion detector and control the same device. But you cannot control the WSM. Here you need a Shelly 1 or 1PM (possibly Mini) and homeassistant.
Helpful answer
One module has two inputs. Yes, 2 lamps are possible. Please note that both must be switches or push-buttons. You can configure switches or push-buttons in the Hue app.
This turns normal switches into Hue switches.
Via homeassitant with shelly plus 2pm , yes. Not directly
Helpful answer
Good evening, no, you need a Philips bridge and Hue equipment.
My understanding is this device allows you to control hue smart lights when you are keeping the normal switches. There is no point to buy this thing to control non hue lightd
Helpful answer
Si
Helpful answer
They are available individually and as a pack of two. The one with 2 costs about 60, the single one about 35, the one you asked for is the 2-pack.
Helpful answer
The switch has no physical connection to the lamp. The cables to the switch and from the switch to the lamp are permanently connected with a Wago. Without internet, this is only possible in the home network. The lamps cannot be controlled without a bridge (de-energising with a fuse or unscrewing and switching on again activates the lamp, however).
The live wire is short-circuited during installation so that the lamp is always lit.
The wall switch module is just a wireless switch that is connected to one (or more) Hue lamp(s).
When the battery is empty, the switching signal is no longer sent to the bridge.
You can of course still control your lamps via the app.
30 of 53 questions