Questions about Digitus 48,3cm 19inch wall cabinet 16HE SoHoline RAL7035 grey H816mmxW600mmxD450mm with glass door

The default is 37 cm from the surface of the mounting rail to the rear wall. However, you can move the rails forward in 2 steps and get a maximum of 4 cm more. But then a device is very close to the pane. This is no longer sufficient for normal patch cables. Then you would have to use 90° angled ribbon cables.

Hello no the cabinet is closed at the bottom and not open. Greetings

Approx. 40 cm. With plug and cable, I would think that the NAS should be max. 35cm deep. I have 2 Synology DSxxx next to each other. But be careful, the door is much further out than the mounting rails, which are inside behind it, so to speak, and above all reach inwards, in the centre and are at 90°. This means that you can either place 1 unusually deep NAS more or less in the centre, which can then be placed at the front towards the door (mounting rails then pass to the left and right, upwards of course; but they just block a good part of the cabinet, because there are more at the back) and so there is plenty of space. Or, if the NAS is very wide or, in other words, if two are to be placed next to each other, you have at least 8 cm less space to the front and rear and the space on the left and right does not extend across the entire width due to the 90° angle of the rails. As I said, a DS918 and a DS1621 stand next to each other, "locked in" by the mounting rails and have an estimated 10-12 cm of space at the back to the rear wall.

The rack was supplied with a cylinder. According to the picture, there is a lock. Did not have to order an additional lock or cylinder.

You're right. I ordered this box few months ago and the ref is DN-19 12-U which correspond to the Unique line.

Never mind. It fits 120mm. I took 5V and fed it directly via USB from the server.

The door can be changed from left to right by loosening the bolts. The external height is 816.20 mm.

You can find a few here at Digitec. I have installed this one: Digitus DN-19 FAN-2 - Rack - Fan Kit - Light Grey a bit loud, but the rack is in the basement....

According to the manufacturer's number it is this product: Digitus DIGITUS 48,3cm 19inch wall-mounted enclosure 16HE SoHoline RAL9002 black without shelf The manufacturer's link also leads to the correct product. Unfortunately, the pictures and specifications do not seem to be quite right.

Hoi - You are looking for a rackmount housing or rack accessories (lugs or rails, or cage nuts with screws? Cable rangers or arms, patch channels etc.?) or a whole rackmount server for a community gameserver that would fit?

The manufacturer would also have a data sheet on his website https://www.assmann.com/de/produkte/?ean=4016032135227 where dimensioned drawings are available. Maybe that will help you.

I bought the same wall cupboard and mine has the vents.

Not sure how to tell the colour, but it's not snow white, it's a relatively light grey.

Mehr Infos inkl Datenblatt mit allen Massen findest du beim Hersteller https://www.digitus.info/en/products/network-and-server-cabinets/network-cabinets-wall-mounting/19-wall-mounting-cabinets-mounted/dn-19-16-u-ec/?PL=de

Unfortunately, I could not find an official set for wall mounting, not even on the manufacturer's product page: https://www.digitus.info/de/produkte/netzwerk-und-serverschraenke/netzwerkschraenke-wandmontage/19-wandgehaeuse-montiert/dn-19-16-u/ On the last page of the data sheet, only the mounting hole spacing is given: https://ftp.assmann.com/pub/DN-/DN-1916-U___4016032135234/DN-1916-U_datasheet_de_Datasheet%20DE_20200224.pdf However, our product experts from customer service will be happy to help you choose suitable screws & dowels: https://helpcenter.digitec.ch/hc/de/requests/new

https://ftp.assmann.com/pub/DN-/DN-1909-U-EC___4016032221708/DN-1909-U-EC_datasheet_de_Datasheet%20DE_20200710.pdf

You will find compatible items in the accessories at the bottom of the page.

If you put it on the floor, it stands well. Maybe some felt glides, rubber feet or castors underneath. E.g. these: Digitus levelling feet for wall boxes and cabinets

Answer from our responsible department: It is difficult, but according to our research, the customer has enough room to use this item for the components he has.

No not really. I have a switch with a fan in it and it can be heard outside pretty well. You would have to buy equipment with passive cooling if you want to have a quiet rack.

According to the information available, the cabinet is delivered without screws, brackets or feet. Article 3528172 fits perfectly.

No. The server enclosure has a depth of 450mm and the cabinet has a total depth of 450mm. This means that objects with a total depth of more than approx. 350mm will not fit. Many standard rack components are deeper than this cabinet allows. Switches, cable routing, a few Synology NAS and others are ok. If you want to be more flexible, you should use a cabinet with at least 60cm usable internal depth (80cm depth).

The cabinet is 450 mm deep.

There are two additional rails from Digitus under the designation "DN-19 MA-WM-EC-16U". Availability is poor, had to wait a few weeks. Not in the range at Digitec.

This refers to the two vertical metal-coloured strips. (Picture 2) The units and fixtures are attached to these 19-inch strips. The 400mm deep cabinets only have these strips at the front behind the door. The 600mm deep cabinets have these strips at the front and back.

Hi, yes you can put floors in this type of cabinet. Personally, I took this => "Digitus DN-19 TRAY-2-SW Fachboden", https://bit.ly/3abhfI3. It does the job perfectly.

There is the required plate. The screws and plugs for fixing to the wall are missing.

The cabinet has a pre-milled opening in the sheet metal at the top and bottom and you can "break out" the piece accordingly, depending on how the cables are fed. The size of the opening is rectangular and quite generous, the question is not whether there is room for all the cables but rather how to close the part so that no dust gets in. I can't measure it right now but I estimate the size to be "the size of an iPhone XR". Hope this helps.

The correct dimensions are LxWxH: 600 x 450 x 816mm.