You're not connected to the Internet.
CHF 18.90

Adafruit Industries Adafruit PowerBoost 1000 Basic 5V USB Boost 1000mA from

PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC...
Art-Nr 5998714
 approx. 5-7 days Currently 5 piece(s) in stock at the supplier

Availability

  • approx. 5-7 days
    Currently 5 piece(s) in stock at the supplier

If ordered immediately.
Information subject to change.

View details

No ratings have been submitted yet for this product.

Rate this product

Description

PowerBoost is the perfect power supply for your power-hungry portable
project! This little DC/DC boost converter module can run from 1.8V
batteries or higher, and convert that voltage to 5.2V DC for running
your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+
from as low as 2V.

We tweaked the output to be 5.2V instead of a straight-up 5.0V so
that there's a little bit of 'headroom' long cables, high draw, the
addition of a diode on the output if you wish, etc. The 5.2V is safe
for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle
Bone while preventing icky brown-outs during high current draw because
of USB cable resistance.

The PowerBoost 1000 has at the heart a TPS61030 boost converter from
TI. This boost converter chip has some really nice extras such as low
battery detection, 4A internal switch, synchronous conversion,
excellent efficiency, and 700KHz high-frequency operation. Check out
these specs!

* Synchronous operation means you can disconnect the output
completely by connecting the ENable pin to ground. This will
completely turn off the output
* 4A internal switch means you can get 1000mA+ from as low as 1.8V,
1500mA+ from 2 NiMH or Alkaline batteries, and at least 2000mA from a
3.7V LiPoly/LiIon battery or 3 NiMH/Alkalines. Just make sure your
batteries can actually supply the required 2-4A, OK?
* Low battery indicator LED lights up red when the voltage dips
below 3.2V, optimized for the most common usage of LiPo/LiIon battery
usage
* On-board 1000mA charge-rate 'Apple/iOS' data resistors. Solder in
the included USB connector and you can plug in any iPhone or iPod for
a speedy 1000mA charge rate. Works with iPads, both mini and 'classic'
type.
* Full breakout for battery in, control pins and power out
* 90%+ operating efficiency in most cases (see datasheet for
efficiency graphs), and low quiescent current: 5mA when enabled and
power LED is on, 20uA when disabled (power and low batt LED are off)

Great for powering your robot, Arduino project, single-board-computer
such as Raspberry Pi or BeagleBone! Each order comes with one fully
assembled and tested PCB, a loose 2-PH JST jack, a 2-pin Terminal
block and a loose USB A jack.

If you are powering your project from USB, solder the USB A jack in (a
3-minute soldering task). Then choose either JST for input (JST is
often used for our LiIon batteries, but the connector is only rated
for 2A) or a terminal block.

The 1000 version comes with a 2-pin terminal block so you can solder
it to the output spot where the USB jack would go. Or don't solder any
connectors in for a more compact power pack and go with 22AWG wires
soldered directly in.

Details:

* Dimensions: 29mm x 23mm x 2mm / 1.1" x .9" x .1"
* Height w/ JST: 7.5mm / .30"
* Weight: 6.0g
more

Specifications

Click 'show more' to display specifications.

General information

Manufacturer Adafruit Industries
Product type Electronics module
Item number5998714
Manufacturer no.ada-2030

Please click directly on the incorrect data to access the registration form.

Alternatively, you can register a generic error-report (wrong picture, unsuitable accessories, etc.)

Cancel

Report incorrect data

Correction suggestion

Comment

Report incorrect data

If you wish to learn more about this product, please visit the manufacturer's website or contact us: galaxus@galaxus.ch

Warranty & right to return

Warranty 24 month Bring-in

Limited right of return

Warranty and return

Please use our simplified returns and warranty process to return a product or register a warranty case. Returns and warranty

Please use our simplified warranty process to view the warranty period as well as any warranty extensions you may have purchased. This will ensure that your return or warranty case is processed quickly and effectively.

Availability

Mail delivery

 Expected delivery time: approx. 5-7 days
Currently 5 piece(s) in stock at the supplier

Collection

All locations

 Expected delivery time: approx. 5-7 days
Currently 5 piece(s) in stock at the supplier

If ordered immediately.
Information subject to change.

Customer questions and answers

No questions so far.

Do you have a question? Ask the Galaxus community.

Ask a question

Ask other customers about product properties, performance or use.

Customer ratings

This product has not yet been rated.

Have you tested this product? Share your opinion with the Galaxus community.

(0)
Rate product
Adafruit Industries Adafruit PowerBoost 1000 Basic 5V USB Boost 1000mA from Adafruit Industries Adafruit PowerBoost 1000 Basic 5V USB Boost 1000mA from